SAE J310:2000 pdf download Automotive Lubricating Greases
1. Scope—This
SAE Recommended Practice was developed by SAE, and the section “Standard Classification and Specification for Service Greases” cooperatively with ASTM, and NLGI. It is intended to assist those concerned with the design of automotive components, and with the selection and marketing of greases for the lubrication of certain of those components on passenger cars, trucks, and buses. The information contained herein will be helpful in understanding the terms related to properties, designations, and service applications of automotive greases.
2. References
2.1 Applicable Publications—The following publications form a part of this specification to the extent specified herein. Unless otherwise specified, the latest issue of SAE publications shall apply.
2.1 .1 SAE P UBLICATIONS —Available from SAE, 400 Commonwealth Drive, Warrendale, PA 1 5096-0001 .
SAE AMS 321 7A—Standard Elastomer Stock – Test Slabs
SAE AMS 321 7/2A—Test Slabs, Acrylonitrile Butadiene (NBR-L) – Low Acrylonitrile, 65-75
SAE AMS 321 7/3B—Test Slabs, Chloroprene (CR) – 67-75
2.1 .2 ASTM P UBLICATIONS —Available from ASTM, 1 00 Barr Harbor Drive, West Conshohocken, PA 1 9428-2959.
ASTM D 1 28—Analysis of Lubricating Grease
ASTM D 21 7—Cone Penetration of Lubricating Grease
ASTM D 566—Dropping Point of Lubricating Grease
ASTM D 942—Oxidation Stability of Lubricating Greases by the Oxygen Bomb Method
ASTM D 972—Evaporation Loss of Lubricating Greases and Oils
ASTM D 1 092—Apparent Viscosity of Lubricating Greases
ASTM D 1 263—Leakage Tendencies of Automotive Wheel Bearing Greases
ASTM D 1 264—Water Washout Characteristics of Lubricating Greases
ASTM D 1 403—Cone Penetration of Lubricating Grease Using One-Quarter and One-Half Scale Cone Equipment
ASTM D 1 404—Test Method for Estimation of Deleterious Particles In Lubricating Grease
ASTM D 1 478—Low-Temperature Torque of Ball Bearing Greases
ASTM D 1 742—Oil Separation from Lubricating Grease During Storage
ASTM D 1 743—Corrosion Preventive Properties of Lubricating Greases
ASTM D 1 831 —Roll Stability of Lubricating Grease
ASTM D 2265—Dropping Point of Lubricating Grease Over Wide-Temperature Range
ASTM D 2266—Wear Preventive Characteristics of Lubricating Grease (Four-Ball Method)
ASTM D 2509—Measurement of Load-Carrying Capacity of Lubricating Grease (Timken Method)
ASTM D 2595—Evaporation Loss of Lubricating Greases Over Wide-Temperature Range
ASTM D 2596—Measurement of Extreme-Pressure Properties of Lubricating Grease (Four-Ball Method)
ASTM D 3336—Test Method for Life of Lubricating Greases in Ball Bearings at Elevated Temperatures
ASTM D 3337—Test Method for Life and Torque of Lubricating Greases in Small Ball Bearings
ASTM D 3527—Life Performance of Automotive Wheel Bearing Grease
ASTM D 3704—Test Method for Wear Preventive Properties of Lubricating Greases Using the (Falex) Block on Ring Test Machine in Oscillating Motion
ASTM D 4048—Test Method for Detection of Copper Corrosion from Lubricating Grease
ASTM D 4049—Test Method for Determining the Resistance of Lubricating Grease to Water Spray
ASTM D 41 70—Fretting Wear Protection by Lubricating Greases
ASTM D 4289—Compatibility of Lubricating Grease with Elastomers
ASTM D 4290—Leakage Tendencies of Automotive Wheel Bearing Grease Under Accelerated Conditions
ASTM D 4693—Low-Temperature Torque of Greased-Lubricated Wheel Bearings
ASTM D 4950—Standard Classification and Specification for Automotive Service Greases
SAE J310:2000 pdf download
